TruGolf Apogee Simulator Bundle

SimSpace Golf Enclosure

We offer in-depth guides, images and videos on how to set up the SimSpace enclosure. For more information, please visit our dedicated page.

TruGolf APOGEE Launch Monitor

Install APOGEE on a flat, level ceiling surface between 9 and 10 feet above the hitting surface. Start by marking the simulator centreline using the supplied reflective dots and laser level, aligning the centre of the hitting area with the screen. Measure the correct tee-to-APOGEE distance based on ceiling height, then mark the ceiling with a plumb bob and fit the ceiling mount securely using the supplied hardware. Slide the unit into the mount, tighten the rear screws, then connect the power cable and CAT6 cable to the unit and simulator computer. Once wired, create or sign in to your E6 profile, redeem your product key, download APOGEE Intelligent Dashboard and E6 software, update the firmware, then run calibration through the dashboard.

SimSpace Golf Enclosure

SIM 0
• Outer Frame: 3.4(w) x 2.6(h) x 1.1(d) metres
• Inner Frame: 3.3(w) x 2.5(h) x 1(d) metres
• Screen: 3.1(w) x 2.3(h) metres / Ratio 4:3*

SIM 1
• Outer Frame: 2.7(w) x 2.6(h) x 1.6(d) metres
• Inner Frame: 2.6(w) x 2.5(h) x 1.5(d) metres
• Screen: 2.4(w) x 2.3(h) metres / Ratio 1:1*

SIM 2
• Outer Frame: 3.1(w) x 2.6(h) x 1.6(d) metres
• Inner Frame: 3.0(w) x 2.5(h) x 1.5(d) metres
- Screen: 2.8(w) x 2.3(h) metres / Ratio 4:3*

SIM 3
• Outer Frame: 3.7(w) x 2.6(h) x 1.6(d) metres
• Inner Frame: 3.6(w) x 2.5(h) x 1.5(d) metres
• Screen: 3.4(w) x 2.3(h) metres / Ratio 4:3*

SIM 4
• Outer Frame: 4.1(w) x 2.6(h) x 1.6(d) metres
• Inner Frame: 4.0(w) x 2.5(h) x 1.5(d) metres
• Screen: 3.8(w) x 2.3(h) metres / 16:10*

SIM 5
• Outer Frame: 3.1(w) x 3.1(h) x 3.1(d) metres
• Inner Frame: 3.0(w) x 3.0(h) x 3.0(d) metres
• Screen: 2.8(w) x 2.8(h) metres / Ratio 1:1*

SIM 6
• Outer Frame: 4.0(w) x 3.1(h) x 3.1(d) metres
• Inner Frame: 4.0(w) x 3.0(h) x 3.0(d) metres
• Screen: 3.8(w) x 2.8(h) metres / Ratio 4:3*

Leave at least 50cm behind & 20cm on either side of the enclosure as a buffer space for ball impacts! All measurements are estimates.

TruGolf APOGEE Launch Monitor

• Mounting type: Ceiling-mounted photometric launch monitor
• Recommended mounting height: 9–10 feet above hitting surface
• Room recommendation: TruGolf recommends 9–10 feet high by 15 feet wide for right- and left-handed players
• Device size: 38 inches wide x 5.5 inches high x 8 inches deep
• Weight: Approximately 22 lbs
• Tee box capture area: 10 inches wide x 8 inches deep
• Ball data measured: Ball speed, back spin, side spin, vertical launch angle and horizontal launch direction
• Club data measured: Club head speed, club face angle and club path
• Camera system: Centre camera and offset camera
• Impact feedback: Slow-motion Point of Impact Replay
• Ball requirements: Measures spin without specialist golf balls
• Club requirements: Records club data without marked clubs in most conditions
• Sticker note: Some lighting conditions or club finishes may require metallic club face stickers for club face angle data
• Placement aid: APOGEE Laser Indicator / Laser Launchpad
• Voice control: “Hey APOGEE” voice command system
• Indicators: System Status Indicator and System Connection Indicator
• Software management: APOGEE Intelligent Dashboard
• Dashboard functions: Status, calibration, tools, support, firmware updates, diagnostics and logs
• Calibration: Automated Calibration Wizard checks installation alignment and ambient light
• Connectivity: CAT6 cable to USB RJ45 adapter, connected to USB 3 port
• Compatible software: E6 CONNECT and E6 APEX
• Minimum E6 CONNECT system requirements: Intel i5 processor, 8GB RAM, Nvidia 1070, 25GB hard drive space, Windows 10 64-bit, internet connection
• Minimum E6 APEX system requirements: Windows 10 64-bit, Intel i7 10th Gen or newer, 16GB RAM DDR4 or better, m.2 NVMe SSD 256GB or better, NVIDIA GeForce RTX 3060 12GB VRAM or better, WiFi 5, full USB 3 connectivity and Gigabit Ethernet